Motorbike Maintenance Plan
12 Month Maintenance Plan
- You are only eligible for this service if you have had one of our main services such as our Wash & Wax carried out on your vehicle within the last 4 weeks. (You will not be eligible if you have had our Maintenance Wash service on your motorbike)
Price:
- £60 Per Motorbike
Time:
Per Motorbike - 2 hours
pH Safe 7-Step Decontamination Wash Process
Pre Wet
Step 1: We pre wet the motorbike and begin to remove any large bits of dirt, grime or contaminants from your motorbike using the water from the pressure washer.
Snow Foam
Step 2: A thick layer of pH safe snow foam will be applied to the entire motorbike. It begins to break down and remove any dirt, grime and contaminants to the surfaces of your motorbike. The snow foam is washed off and exposes the areas that have got particularly stubborn bits of grime that will need more specific products to be applied to remove them.
Bug Removal
Step 3: We apply one of our specialist pH safe products to any areas of your bike that have got bug splats, bird poo marks, tree sap, grease and grime on it. We end up covering most of your motorbike during this step, only working in small sections at a time as we gently massage it around with one of our brushes. After we complete each section, we give it a rinse with water and re check the surface, if there are still any bugs or bits of grime left on, we will repeat the process once more.
Wheels & Brakes
Step 4: We then move onto your wheels and brake callipers, depending on the material and finish of these items we have a variety of different pH safe products that gently clean and remove any contaminants that you would find on them without damaging or staining them in the process.
Degreasing
Step 5: We then move the focus to your engine, swingarm, rear sets and exhaust system where we apply one of or a mix of the pH safe and other specialist products we use to degrease and remove tar, oils, dirt and grime from these areas.
Iron Fallout
Step 6: We will carry out our iron fallout removal step every 3-6 washes, depending on the levels of contamination your motorbike has.
Depending on the condition and type of materials used on your motorbike, we will use one of our pH safe iron fallout remover products. This product breaks down and safely removes the iron particulates that are bonded to the paint's surface.
3 Bucket Shampoo Wash
Step 7: Our 3 bucket safe wash is designed to protect your paintwork and other sensitive areas as good as we can during this process. We use an extremely high quality pH safe shampoo that provides superb cleaning power whilst also protecting your sensitive paintwork. It does this because it contains a lot of surfactants, detergents and lubricants, these help to encapsulate and safely remove any nasty bits of dirt or grime that may cause damage to your paintwork. We then give your motorbike a thorough rinse down, afterwards we have a thorough check over to make sure we have got every part of it cleaned to our standards.
Drying Phase
We now move onto the drying process where we use a combination of warm blown air and extremely plush drying towels to get rid of as much of the water as possible.
Wax or Ceramic Sealant Applied
We then move onto applying one of our professional grade waxes or ceramic sealants to all the paintwork of your car. It is then allowed to cure and once ready we buff and polish it off by hand. The results are astonishing, it rejuvenates the depth of colour and gloss of your paintwork and keeps the hydrophobic protection topped up
Dressing The Trim
Often overlooked the black plastic trim and any other types of trim your motorbike has eventually begins to lose the oils from within it and ends up degrading over time, the products we use helps to restore and rejuvenate the trim leaving it with a lasting finish that really makes your motorbike stand out.
Chain, Chain Sliders & Sprockets
For chain driven motorbikes we move onto the cleaning of the chain, chain sliders and rear sprocket (We will also clean the front sprocket if it is easily accessible or open already to us). Once cleaned, we will re-lube the chain with either a wet/dry/wax based lube, depending on your preference.
The Finishing Touches
Your brake rotors are given a once over with a high quality brake cleaner to make sure any traces of the products we have used are completely removed.Your bike is then given a thorough check over to make sure we have cleaned all the various parts to our standards. We will then use a variety of products if needed to add any remaining finishing touches to your pride and joy.
Pre Inspection Form sent to you via email which will contain:
- Tyre depth
- Any damage or wear and tear found on the vehicle
- Additional comments
